Tile Roofing Gilbert logo
Two-story tan stucco house with a terracotta concrete S-tile roof, one section stripped to new underlayment and battens with tile stacked for re-laying

Tile roofing in Gilbert, AZ

Flat Tile Roofing in Gilbert, AZ

  • Typical cost: HomeGuide's national table lists flat or plain tile at $7 to $21.50 per sq ft, installed.
  • Profile: "low" or flat tile has a top-surface rise of 1/2 inch or less, by the TRI definition.
  • Clay flat weight: small flat clay shingles can reach 1,300 to 2,000 lb per square (100 sq ft) and want at least a 5:12 slope, by one maker's spec.
  • Labor: Angi calls flat tile straightforward to lay out. HomeGuide says flat shingle tiles take more time to install than interlocking tiles.

Tile Roofing Gilbert forwards your details to an independent tile roofer nearby for flat tile, whether it's a repair on a slate-look roof or a new flat-tile re-roof. The cost figure is a national table range; a bid on your roof can fall anywhere in it or outside it. Knowing the roof's pitch helps, because the slope rules further down decide what can go on.

Get a free tile roofing estimate

Free for homeowners and HOAs. One local contractor contacts you.

Flat Tile Roofing Profiles

HomeGuide notes that low or flat concrete tiles often imitate slate or wood. In practice the choice comes down to three looks, plus the slope limits that apply to tile of every profile.

Charcoal slate-look flat concrete tile roof with crisp straight courses on a modern tan stucco home

Slate-Look Flat Tile

Slate-look tile copies the thin, square-edged courses of natural slate. Eagle, for example, sells a Tapered Slate profile in standard weight. Natural slate is a different product: HomeGuide prices flat slate at $10 to $30 per sq ft installed. HomeGuide also describes flat roof tile as interlocking, in smooth or textured finishes.

Brown shake-look flat concrete tile roof with wood-grain texture and shadow lines on a stucco ranch house

Shake-Look Flat Tile

Shake-look tile gives a wood roof's texture without the wood. Eagle describes its Ponderosa as having textured shadow lines for a wood look, and calls it a more durable and affordable alternative to natural shake. Eagle pairs it with farmhouse, craftsman and bungalow styles. Moving from a non-tile roof to tile is covered on the shingle to tile conversion page.

Smooth flat sand-colored concrete tile roof with clean square butt edges on a contemporary stucco house

Smooth Flat Tile

Smooth flat tile is the plainest look, with clean lines and a square butt edge. Eagle pairs its Bel Air with transitional and modern houses. In clay, Ludowici's flat slab shingle is the same idea at a very different weight:

  • 6 by 12 inch pieces, 480 per square, at a 6 by 5 inch exposure
  • 1,300 lb per square at 3/8 inch thick; 2,000 lb at 5/8 inch
  • Listed minimum slope: 5:12

Concrete flat profiles weigh less than that; the standard and lightweight figures are on the concrete tile roofing page.

Low-pitch flat concrete tile roof over a single-story stucco wing with a membrane edge visible at the eave

Flat Tile on Lower Slopes

The low-slope limits here apply to every tile profile, not just flat; the flat-specific number on this page is Ludowici's 5:12 minimum for its clay slab, above. Tile needs at least 2.5:12 under the code, with extra underlayment up to 4:12; the underlayment replacement page has the exact rules. TRI's manual sets two more lines:

  • Below 3:12: tile is considered decorative, and a multi-ply or single-ply membrane roof goes on first.
  • 3:12 up to 4:12: self-adhered ASTM D1970 underlayment, two layers of No. 30 felt, a single-ply membrane or another approved system.

Lightweight flat tile and its trade-offs belong to the concrete tile roofing page.

Gloved hands setting a flat concrete roof tile onto a wooden batten over new dark underlayment

Why Gilbert homeowners and HOAs call Tile Roofing Gilbert

  • One request goes to one roofer, never to a call list
  • Free to send, with nothing to sign until you have a written price
  • Ask to see the R-42 or CR-42 license number on the contract
  • Ask how many replacement tiles the price allows for
  • You pay nothing for the introduction

Get a free tile roofing estimate

Free for homeowners and HOAs. One local contractor contacts you.

Flat Tile or S-Tile: What Changes

If you're weighing flat tile against S-tile on a Gilbert house, the price isn't the deciding factor. HomeGuide's installed range for Spanish tile, $7 to $21 per sq ft, sits almost on top of the flat range at the top of this page. The real differences:

  • Eave parts

    TRI requires bird stop on high-profile tile and makes it optional on low and medium profiles, so a flat roof usually needs less at the eave.
  • Breakage

    HomeGuide rates flat tile as more crack-resistant than barrel tile.
  • Deck condition

    HomeGuide advises installing flat roof tiles on new or leveled trusses and decking.
  • Switching profiles

    going from S-tile to flat means new tile, so it isn't a re-lay, and it may need HOA approval. Gilbert's re-roof permit exemption covers only work with no structural change, so a switch that needs reframing takes a permit. See the replacement page and the HOA tile roofing page.

Ready to get started in Gilbert?