Tile Roofing Gilbert logo
Two-story tan stucco house with a terracotta concrete S-tile roof, one section stripped to new underlayment and battens with tile stacked for re-laying

Tile roofing in Gilbert, AZ

Spanish Tile Roofing in Gilbert, AZ

  • Cost on the roof: HomeGuide prices Spanish (S) tile at $7 to $21 per sq ft installed, or $10,500 to $52,500 for a typical roof, nationally.
  • Material: most Spanish tile is terracotta clay or concrete; clay S tile alone costs $2.50 to $11 per sq ft.
  • Profile class: the industry calls S tile "high profile" once its rise is more than one-fifth of its width.
  • Eave: high-profile tile needs a bird stop at the first course under the TRI installation manual; on lower S profiles it's optional unless the building official asks.
  • Overlap: every course keeps at least a 3-inch head lap unless the tile's design rules it out.

Tile Roofing Gilbert carries your S-tile request to a local tile roofer, whether the job is trim, a re-lay or a whole new Spanish roof. HomeGuide's ranges are for checking a bid, and no one has quoted your house from them.

Get a free tile roofing estimate

Free for homeowners and HOAs. One local contractor contacts you.

Spanish Tile Roofing Options in Gilbert

"Spanish tile" and "S-tile" are the same thing: an interlocking tile whose cross-section makes a wave across the roof. What separates one S roof from another is how tall the wave is, which trim pieces finish it, and the color blend.

Deep wave high-profile terracotta concrete S tile roof over a sand stucco house with desert landscaping

High-Profile S Tile

The deep S is the classic Spanish roof. Eagle describes its Capistrano as a high S-barrel profile suited to Spanish, Tuscan and Mediterranean houses with stucco walls. In TRI's terms, a high-profile tile has a rise greater than one-fifth of its width, measured as installed, and that class covers S, barrel and two-piece pan-and-cover tile.

  • Rise-to-width ratio: more than 1:5
  • Bird stop at the eave: required by the TRI installation manual (industry guidance, not code)
  • HomeGuide's rule of thumb for concrete: a curve of 1 inch or more for every 5 inches of tile width
Gentle low-profile S tile roof in a brown blend on a single-story stucco ranch house

Medium-Profile S Tile

A flatter S keeps the wave but casts a softer shadow. Eagle pitches its Malibu, with "gentle curves," at contemporary houses and low-pitched rooflines. TRI calls this middle band medium profile: a rise over 1/2 inch but no more than one-fifth of the width. HomeGuide's version for concrete is a curve under 1 inch per 5 inches of width. The practical difference on your roof is at the eave: TRI makes bird stop optional on medium-profile tile unless the building official requires it.

Close view of an S tile roof gable with rake trim tiles and a ridge line of rounded caps against blue sky

S-Tile Trim: Rake, Ridge and Eave Closure

Field tile is only part of an S roof. TRI's glossary lists the trim that finishes it:

  • Rake trim: covers the joint where the roof meets the gable end
  • Hip starter and hip/ridge tile: close the outside corners and the peak
  • Eave closure: fills the convex gap under the first course of S or pan-and-cover tile and sets that course at the right rise
  • Weather blocking: a moldable or preformed barrier against wind-driven rain where field tile meets trim or flashing

Rebedding loose ridge caps is covered on the ridge cap repair page, and replacing eave closures on the bird stop page.

Mixed terracotta, rust and brown blend S tiles laid across a roof plane in afternoon sun

S-Tile Color Blends

Many S roofs are blends rather than a single color, and Eagle alone listed over 150 colors across 10 profiles in 2017. TRI's manual says small variations in sand, cement and oxide cause slight shading from tile to tile. To avoid stripes, stair-steps or hot spots, tile should be spread across the whole roof plane as it's loaded, and mixed on the way up for a random blend. Ask how the crew loads a blend. A roof loaded pallet by pallet can show bands you'll see from the street.

Concrete vs Clay S Tile

Both materials come in the S shape. By weight, Eagle lists its standard concrete Capistrano S at about 900 lb per 100 sq ft, and a one-piece clay S runs 788 to 840 lb per square. Clay holds its color longer and costs more; concrete is the budget option. The numbers for each, including weights per square and expected life, sit on the concrete tile roofing and clay tile roofing pages.

Gloved hands setting a flat concrete roof tile onto a wooden batten over new dark underlayment

Why Gilbert homeowners and HOAs call Tile Roofing Gilbert

  • One request goes to one roofer, never to a call list
  • Free to send, with nothing to sign until you have a written price
  • Ask to see the R-42 or CR-42 license number on the contract
  • Ask how many replacement tiles the price allows for
  • You pay nothing for the introduction

Get a free tile roofing estimate

Free for homeowners and HOAs. One local contractor contacts you.

What to Ask Before an S-Tile Job

Angi notes that the overlapping S design needs careful placement, which adds a little labor compared with flat tile. That labor goes into a few details worth checking in the bid:

  • Head lap

    TRI calls for a minimum 3-inch head lap on all tile courses. Tiles spread wider than that to save pieces let water in; the tile roof leak repair page covers what that looks like.
  • Eave treatment

    solid or vented bird stop, a metal eave closure, or an eave riser. TRI allows either solid or vented bird stop.
  • Ridge method

    how the ridge tile is set and how the ridge is vented.
  • Spares

    ask for a few boxes of leftover field tile and trim. S-tile colors get discontinued, and spares are the cheapest match you'll ever find.
  • Layout

    TRI suggests dividing each slope into equal courses so the last full tile lands cleanly at the ridge.

Ready to get started in Gilbert?